[Jun 28, 2026] New Juniper JN0-649 Dumps with Test Engine and PDF (New Questions)
Pass Your JN0-649 Exam Easily - Real JN0-649 Practice Dump Updated
NEW QUESTION # 49
Click the Exhibit button.
You have configured and applied the policer shown in the exhibit to your Junos device.
Which statement is true in this scenario?
- A. Traffic exceeding the committed-burst size will be discarded.
- B. Traffic exceeding the excess-burst size will be discarded.
- C. Traffic exceeding the committed-burst size will be marked with a loss priority of high.
- D. Traffic exceeding the committed-information-rate will be rate limited.
Answer: B
Explanation:
Red--Traffic that exceeds the burst size for peak traffic (EBS), single-rate marks packets with an implicit loss priority of high and, optionally, discards the packets.
https://www.juniper.net/documentation/en_US/junos/topics/topic-map/policer-single-rate-three- color.html
https://www.juniper.net/documentation/us/en/software/junos/routing-policy/topics/topic- map/policer-single-rate-three-color.html
NEW QUESTION # 50
You have multiple BGP routes to the same prefix with equal local-preference values and AS-path lengths.
In this scenario, which route will be preferred in the route selection process?
- A. The route with the highest MED value.
- B. The route with the most preferred origin value.
- C. The route with the lowest MED value.
- D. The route with the least preferred origin value.
Answer: B
Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/reference/general/routing-protocols- address-representation.html
NEW QUESTION # 51
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. The host that the route is associated with is multihomed to two leaf nodes.
- B. The route is a Type 2 EVPN route.
- C. The host that the route is associated with is single-homed to one leaf node.
- D. The route is a Type 1 EVPN route.
Answer: B,C
NEW QUESTION # 52
Your IPv4 multicast network uses different MX Series routers for the source DR and the PIM sparse-mode RP.
What is required before PIM register messages are exchanged between the DR and RP routers?
- A. Add a tunnel services PIC to the RP router.
- B. Add an adaptive services PIC to the DR router.
- C. Configure PIM encapsulation on the DR and RP routers.
- D. Enable tunnel services on the DR and RP routers.
Answer: D
NEW QUESTION # 53
When using wide metrics, which two statements about route advertisement between IS-IS levels are correct? (Choose two.)
- A. If wide-metrics-only is configured, Level 1 routes are not advertised to Level 2 routers by default.
- B. Level 1 routes are advertised to Level 2 routers by default.
- C. Level 1 and Level 2 routers do not advertise Level 2 routes into the Level 1 area by default.
- D. Level 1 routes advertised as external routes into Level 1 are not advertised to any Level 2 routers by default.
Answer: A,C
NEW QUESTION # 54
A Layer 2 connection does not expend across data centers. The IP subnet in a Layer 2 domain is confined within a single data center.
Which EVPN route type is used to communicate prefixes between the data centers?
- A. Type 1
- B. Type 2
- C. Type 4
- D. Type 5
Answer: D
Explanation:
https://www.juniper.net/documentation/us/en/software/junos/evpn-vxlan/topics/concept/evpn-route-type5-understanding.html#:~:text=In%20the%20control%20plane%2C%20EVPN,subnet%20connectivity%20across%20data%20centers.
NEW QUESTION # 55
You are asked to troubleshoot voice quality issues on your newly implement VoIP network. You notice that the voice packets are being dropped. You have verified that the packets are correctly marked for expedited forwarding queue.
Referring to the exhibit, what must you configure to solve the problem?
You are asked to troubleshoot voice quality issues on your newly implement VoIP network. You notice that the voice packets are being dropped. You have verified that the packets are correctly marked for expedited forwarding queue.
Referring to the exhibit, what must you configure to solve the problem?




- A. You must configure a scheduler to allocate bandwidth to the expedited forwarding queue.
- B. You must configure a policer to ensure that the queue is not being starved.
- C. You must configure a multifield classifier to put the VoIP traffic in the correct queue.
- D. You must configure a rewrite rule to ensure that the traffic is scheduled properly in the device.
Answer: A
NEW QUESTION # 56
You are configuring MVRP for automatic VLAN registration. Which two statements are true?
(Choose two.)
- A. MVRP must be configured on all trunk ports
- B. the trunk port must not be configured with vlan members
- C. the trunk port must be configured with "vlan all"
- D. MVRP must be configured on all access ports
Answer: A,B
NEW QUESTION # 57
You have configured MSTP in your Layer 2 network.
You are having problems with it establishing correctly.
Referring to the exhibit, what is causing the problem?
- A. You must assign a context ID number other than zero
- B. The MSTI-to-VLAN mapping does not match
- C. The revision number is the same on both devices
- D. The region name is not correct
Answer: B
NEW QUESTION # 58
Which two statements about BGP communities are true? (Choose two.)
- A. A prefix can belong to more than community.
- B. A community is not a transitive attribute.
- C. A prefix can only belong to one community.
- D. A BGP device can set, append, or modify the community of a route.
Answer: C,D
NEW QUESTION # 59
Your EX Series switch has IP telephones and computers connected to a single switch port. You are considering implementing the voice VLAN feature to help with this setup.
In this scenario, which two statements are correct? (Choose two.)
- A. Assigning the incoming voice and data traffic to separate VLANs enables the ability to prioritize the traffic using CoS.
- B. The voice VLAN feature must be used with LLDP-MED to associate VLAN ID and 802.1p values with the traffic.
- C. The voice VLAN feature will enable incoming tagged data and voice traffic to be associated with separate VLANs.
- D. The interfaces must be configured as access ports.
Answer: A,D
NEW QUESTION # 60
Referring to the outputs shown in the exhibit, which two statements are correct about the IS-IS adjacency?
(Choose two.)
- A. R2 is configured to participate in Level 2 only.
- B. R1 is configured to participate in both Level 1 and Level 2.
- C. R1 is configured to participate in Level 2 only.
- D. R2 is configured to participate in both Level 1 and Level 2.
Answer: A,B
Explanation:
From the provided IS-IS adjacency outputs:
* R1 is configured to participate in both Level 1 and Level 2 (A): This is indicated by the adjacency states for both Level 1 and Level 2 on the R1 interfaces.
* R2 is configured to participate in Level 2 only (D): This is shown by the adjacency state for Level 2 only on the R2 interfaces.
References:
* The IS-IS adjacency outputs indicate the state and levels of participation for each router.
* Configuration and command references from "Example configs for VMRCAXP01W.txt" and other
* documents provide context for understanding IS-IS states and levels.
NEW QUESTION # 61
You want to provide Layer 2 connectivity between campus sites using Ethernet switches through a metro Ethernet service provider who is using Q-in-Q tagging on their network.
Referring to the exhibit, what are two design considerations in this environment? (Choose two.)
- A. Each campus switch shown must have a C-Tag 300 configured.
- B. L2PT is required on the SP network to support the spanning tree protocol.
- C. VXLAN could be implemented on your network across this service provider network.
- D. Each campus switch shown must have S-Tag 300 configured.
Answer: B,D
NEW QUESTION # 62
When configuring class of services, what would be you use to allocate bandwidth to a forwarding class?
- A. bandwidth
- B. transmit rate
- C. speed
- D. buffer depth
Answer: B
NEW QUESTION # 63
You are asked to implement fault tolerant RPs in your multicast network.
Which two solutions would accomplish this behavior? (Choose two.)
- A. Use BFD with statically defined RPs.
- B. Use anycast PIM with statically defined RPs.
- C. Use MSDP with statically defined RPs.
- D. Use IGMPv3 with statically defined RPs.
Answer: B,C
NEW QUESTION # 64
A modified deficit round-robin scheduler is defined by which three variables? (Choose three.)
- A. priority
- B. Layer 3 fields
- C. transmit rate
- D. buffer size
- E. WRED
Answer: A,C,D
Explanation:
To configure MDRR, configure a scheduler at the [edit class-of-service schedulers] hierarchy level:
content_copy zoom_out_map
[edit class-of-service schedulers]
scheduler-name {
buffer-size (seconds | percent percentage | remainder | temporal microseconds); priority priority-level; transmit-rate (percent percentage | rate | remainder) <exact | rate-limit>;
}
https://www.juniper.net/documentation/us/en/software/junos/cos/topics/concept/cos-configuring- mdrr-on-enhanced-queuing-dpcs.html
NEW QUESTION # 65
Referring to the configuration shown in the exhibit, how many of the routes received from 10.0.0.2 will be active in the routing table?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 66
Your EX Series switch has IP telephones and computers connected to a single switch port. You are considering implementing the voice VLAN feature to help with this setup. In this scenario, which two statements are correct? (Choose two.)
- A. The voice VLAN feature will enable incoming tagged data and voice traffic to be associated with separate VLANs.
- B. The interfaces must be configured as access ports.
- C. Assigning the incoming voice and data traffic to separate VLANs enables the ability to prioritize the traffic using CoS.
- D. The voice VLAN feature must be used with LLDP-MED to associate VLAN ID and 802.1p values with the traffic.
Answer: B,D
Explanation:
EX Series switches can accommodate an IP telephone and end host connected to a single switch port. In such a scenario, voice and data traffic must be separated into different broadcast domains, or VLANs. One method for accomplishing this is by configuring a voice VLAN, which enables access ports to accept untagged data traffic as well as tagged voice traffic from IP phones, and associate each type of traffic with separate and distinct VLANs. Voice traffic (tagged) can then be treated differently, generally with a higher priority than data traffic (untagged).
NEW QUESTION # 67
Your network has Junos Fusion configured with MX960 routers as aggregation devices (AD) and QFX5100 switches as satellite devices (SO) Which two statements are coned in this scenario?
(Choose two )
- A. The AD runs the Junos software for all its connected SDs.
- B. The Fusion extended ports are configured on the SDs.
- C. All SDs connected to a single AD must use the same software version.
- D. SDs are added to the AD by configuring the cascade port on the AD.
Answer: B,D
NEW QUESTION # 68
Which statement is correct about IS-IS?
- A. IS-IS uses areas and an autonomous system.
- B. Level 1 routers route traffic between autonomous systems.
- C. Level 2 routers must share the same area address.
- D. Level 1/2 routers automatically inject a default route to the nearest Level 1 router.
Answer: A
Explanation:
Level 1/2 routers automatically inject a default route to the nearest Level 1 router.
It's the other way around.
NEW QUESTION # 69
You are configuring, the PVLAN feature on your switches. The PVLAN will span the two EX Series switches shown in the exhibit.
Which three configuration parameters must be enabled on the ports connecting the two switches?
(Choose three. )
- A. interface-mode trunk
- B. family inet
- C. interface-mode access
- D. inter-switch-link
- E. family Ethernet-switching
Answer: A,D,E
NEW QUESTION # 70
You must provide network connectivity to hosts that fail authentication.
In this scenario, what would be used in a network secured with 802.1X to satisfy this requirement?
- A. Use the server-reject-vlan command to specify a guest VLAN.
- B. Configure a secondary IP address on the port for unauthenticated hosts.
- C. Configure the native-vlan-id parameter on the port.
- D. Configure the port as a spanning tree edge port.
Answer: A
Explanation:
* Understanding 802.1X Authentication:
* 802.1X is a network access control protocol that restricts access until the device or user is authenticated.
* Guest VLAN Configuration:
* When hosts fail authentication, they need to be placed in a separate VLAN to provide limited network access.
* server-reject-vlan Command:
* This command configures a VLAN for unauthenticated devices.
* Ensures that devices that fail authentication are placed in a designated guest VLAN.
* Configuration Example:
shell
Copy code
set protocols dot1x authenticator interface ge-0/0/1.0 server-reject-vlan guest-vlan References:
* Juniper 802.1X Authentication Configuration Guide
* Juniper Guest VLAN Configuration
NEW QUESTION # 71
You are asked to troubleshoot voice quality issues on your newly implement VoIP network. You notice that the voice packets are being dropped. You have verified that the packets are correctly marked for expedited forwarding queue.
Referring to the exhibit, what must you configure to solve the problem?


- A. You must configure a scheduler to allocate bandwidth to the expedited forwarding queue.
- B. You must configure a policer to ensure that the queue is not being starved.
- C. You must configure a multifield classifier to put the VoIP traffic in the correct queue.
- D. You must configure a rewrite rule to ensure that the traffic is scheduled properly in the device.
Answer: A
NEW QUESTION # 72
You are asked to enforce user authentication using a captive portal before users access the corporate network.
Which statement is correct in this scenario?
- A. All Web browser requests are redirected to the captive portal until authentication is successful.
- B. HTTPS is the default protocol for a captive portal.
- C. When enabled, a captive portal must be applied to each individual interface.
- D. A captive portal can be bypassed using an allowlist command containing a device's IP address.
Answer: A
Explanation:
Captive Portal Functionality:
* Captive portals are used to enforce user authentication by redirecting web browser requests to a login page until authentication is successful.
Operation:
* When a user connects to the network, their HTTP requests are intercepted and redirected to the captive portal login page. This process continues until the user provides valid credentials.
Implementation:
* Juniper Configuration:
shell
Copy code
set security authentication-web redirect-url "http://<captive-portal-url>" set security zones security-zone <zone> interfaces <interface> host-inbound-traffic system-services http set security zones security-zone <zone> interfaces <interface> host-inbound-traffic system-services https set access profile <profile-name> captive-portal
* This configuration ensures that all HTTP/HTTPS traffic is redirected to the specified captive portal for authentication.
References:
* Detailed configuration and operation are documented in "Tech Ops Managed Router Juniper Install Guide" and related documents.
NEW QUESTION # 73
Which protocol is used for port-level access control and authentication?
- A. AES
- B. 802.1x
- C. MD5
- D. IPsec
Answer: B
NEW QUESTION # 74
......
To be eligible for the JNCIP-ENT exam, candidates should have a minimum of three years of experience in enterprise networking, preferably with experience in Juniper Networks technologies. They should have a good understanding of various networking technologies and protocols, and they should have completed the Juniper JNCIS-ENT (Enterprise Routing and Switching, Specialist) certification.
Actual4Cert just published the Juniper JN0-649 exam dumps!: https://pass4sure.actual4cert.com/JN0-649-pass4sure-vce.html